Home Categories Send inquiry

Sodium Salicylate CAS 54-21-7 USP35 Standard


Sodium Salicylate
C7H5NaO3 160.10
Benzoic acid, 2-hydroxy-, monosodium salt;
Monosodium salicylate [54-21-7]; UNII: WIQ1H85SYP.
DEFINITION
Sodium Salicylate contains NLT 98.0% and NMT 102.0% of sodium salicylate (C7H5NaO3), calculated on the anhydrous basis.
IDENTIFICATION
Change to read:
• A. SPECTROSCOPIC IDENTIFICATION TESTS <197>, Infrared Spectroscopy: 197K (CN 1-MAY-2020)
• B. IDENTIFICATION TESTS-GENERAL, Sodium <191>
Sample solution: 50 mg/mL of Sodium Salicylate in water
Analysis: Proceed as directed for Sodium in the chapter.
Acceptance criteria: Meets the requirements
• C. The retention time of the major peak of the Sample solution corresponds to that of the Standard solution, as obtained in the Assay.
ASSAY
• PROCEDURE
Mobile phase: Methanol, trifluoroacetic acid, and water (40:0.1:60)
Standard solution: 0.04 mg/mL of USP Sodium Salicylate RS in Mobile phase
Sample solution: 0.04 mg/mL of Sodium Salicylate in Mobile phase
Chromatographic system
(See Chromatography <621>, System Suitability.)
Mode: LC
Detector: UV 212 nm
Column: 2.1-mm × 5-cm; 1.7-µm packing L1
Column temperature: 30°
Flow rate: 0.2 mL/min
Injection volume: 2 µL
System suitability
Sample: Standard solution
Suitability requirements
Tailing factor: 0.8-1.8
Relative standard deviation: NMT 0.73%
Analysis
Samples: Standard solution and Sample solution
Calculate the percentage of sodium salicylate (C7H5NaO3) in the portion of Sodium Salicylate taken:
Result = (ru /rs ) × (Cs /Cu ) × 100
ru= peak response from the Sample solution
rs= peak response from the Standard solution
Cs= concentration of USP Sodium Salicylate RS in the Standard solution (mg/mL)
Cu= concentration of Sodium Salicylate in the Sample solution (mg/mL)
Acceptance criteria: 98.0%–102.0% on the anhydrous basis
IMPURITIES
• SULFITE or THIOSULFATE
Sample solution: 1.0 g of Sodium Salicylate in 20 mL of water
Analysis: Add 1 mL of hydrochloric acid to the Sample solution, and filter the liquid.
Acceptance criteria: NMT 0.15 mL of 0.10 N iodine is required to produce a yellow color in the filtrate.
• ORGANIC IMPURITIES
Mobile phase: Methanol, trifluoroacetic acid, and water (40:0.1:60)
Standard stock solution: 0.125 mg/mL of USP Sodium Salicylate RS, 0.25 mg/mL of USP Salicylic Acid Related Compound A RS,
0.125 mg/mL of USP Salicylic Acid Related Compound B RS, and 0.05 mg/mL of USP Phenol RS in Mobile phase
Standard solution: 1.25 µg/mL of USP Sodium Salicylate RS, 2.5 µg/mL of USP Salicylic Acid Related Compound A RS, 1.25 µg/mL of
USP Salicylic Acid Related Compound B RS, and 0.5 µg/mL of USP Phenol RS in Mobile phase from Standard stock solution
Sample solution: 2.5 mg/mL of Sodium Salicylate in Mobile phase
Chromatographic system
(See Chromatography <621>, System Suitability.)
Mode: LC
Detector: UV 212 nm
Column: 2.1-mm × 5-cm; 1.7-µm packing L1
Column temperature: 30°
Flow rate: 0.2 mL/min
Injection volume: 2 µL
System suitability
Sample: Standard solution
Suitability requirements
Resolution: NLT 3.0 between salicylic acid related compound A and phenol; NLT 3.0 between phenol and salicylic acid related compound B
Relative standard deviation: NMT 2% for each peak
Analysis
Samples: Standard solution and Sample solution
Calculate the percentage of salicylic acid related compound A, salicylic acid related compound B, or phenol in the portion of
Sodium Salicylate taken:
Result = (ru /rs ) × (Cs /Cu ) × 100
ru= peak response of salicylic acid related compound A, salicylic acid related compound B, or phenol from the Sample solution
rs= peak response of salicylic acid related compound A, salicylic acid related compound B, or phenol from the Standard solution
Cs= concentration of USP Salicylic Acid Related Compound A RS, USP Salicylic Acid Related Compound B RS, or USP Phenol RS in the Standard solution (mg/mL)
Cu= concentration of Sodium Salicylate in the Sample solution (mg/mL)
Calculate the percentage of any other individual impurity in the portion of Sodium Salicylate taken:
Result = (ru /rs ) × (Cs /Cu ) × 100
ru= peak response of any other individual impurity from the Sample solution
rs= peak response of salicylic acid related compound B from the Standard solution
Cs= concentration of USP Salicylic Acid Related Compound B RS in the Standard solution (mg/mL)
Cu= concentration of Sodium Salicylate in the Sample solution (mg/mL)
Acceptance criteria: See Table 1.
Table 1
Name Relative Retention Time Acceptance Criteria, NMT (%)
Salicylic acid related compound A 0.3 0.1
Phenol 0.4 0.02
Salicylic acid related compound B 0.6 0.05
Salicylic acid 1.0 –
Any other individual impurity – 0.05
Total impurities – 0.2
SPECIFIC TESTS
• WATER DETERMINATION, Method I<921>: NMT 0.5%
ADDITIONAL REQUIREMENTS
• PACKAGING AND STORAGE: Preserve in well-closed, light-resistant containers.
• USP REFERENCE STANDARDS <11>
USP Salicylic Acid Related Compound A RS
4-Hydroxybenzoic acid.
C7H6O3 138.12
USP Salicylic Acid Related Compound B RS
4-Hydroxyisophthalic acid.
C8H6O5 182.13
USP Sodium Salicylate RS

Shanghai Ruifu Chemical Co., Ltd. is the leading supplier of Sodium Salicylate (CAS: 54-21-7) with high quality, production capacity 3000 tons per year, can meet the specifications of USP35, BP2010, EP11.0.
Ruifu Chemical can provide worldwide delivery, competitive price, small and bulk quantities available.
If you are interested in Sodium Salicylate, please send detailed information includes CAS number, product name, quantity to us. Please contact us by e-mail: alvin@ruifuchem.com

Contact: Dr. Alvin Huang

Mobile/Wechat/WhatsApp: +86-15026746401

E-Mail: alvin@ruifuchem.com